Isostatic pressing for ceramic products

For pressing of round and multi-edge oval and non- symmetric flat or deep ware of spray-dried porcelain granulate or similar ceramic body.
Is nowadays the most suitable and cost-effective method of producing either small or large amounts of tableware.

PRESSES FOR CERAMIC TABLEWARE

ISOSTATIC PRESSING FOR CERAMICS PRODUCTS

For pressing of round and multi-edge oval and non-symmetric flat or deep ware of spray-dried porcelain granulate or similar ceramic body.
Is nowadays the most suitable and cost-effective method of producing either small or large amounts of tableware.

PRESSES FOR CERAMIC TABLEWARE

THE ADVANTAGES OF​ SAMA PRESSES

1
All PHO Green presses are equipped with an energy saving hydraulic system with low electrical consumption and lower cooling water requirements.
2
Excellent guidance of press cylinder on two tie rods to avoid any tiltings of press cylinder and tool.
3
SIEMENS SPS Control Board for easy programming and maintenance.
4
Oil tank under pressure above the machine. To avoid infiltration of air and for fast hydraulic functioning.
5
Press frame made of cast iron for perfect stability and vibration-free execution.
6
Suitable for all tool systems (vacuum or pressure filling).
LPP-1S-38 ceramic products press

PHO451 ceramic products press

isostatic press

In addition to the conventional round-shaped, non-round or multi-angular tableware items, this machine is also suitable for small and deep ceramic items, up to two moulds.

LPP-1-45/OFM press for ceramic tableware

PHO700 press for ceramic tableware

isostatic press

This isostatic production system for flatware is able to produce flat structured plates, irregular-shaped soup bowls or plates with festooned lip.

Technical Features um PHO451 PHO700
Output round flatware up to pieces/hour 500 450
Article height mm max. 110 max. 150
Article diameter - unfired mm min. 110 – max. 380 min. 110 – max. 480
Flat plates up to mm max. 390 max. 410
Closing force KN 4.500 7.000

ISOSTATIC TOOLS

Made of aluminium and steel, to be installed in the isostatic press, for the forming of different article shapes and dimensions at max pressure 300 bar.

ISOSTATIC TOOLS

the advantages of our tools

1
No wear and tear parts with Netzsch tool system
2
Centering system for quick tool exchange
3
Execution of membranes and linings with  adiprene or polyurethane according to complexity of articles  
4
In-house expertise for tool design, manufacturing  and tool training
5
Reduced amount of parts for easy manufacturing and optimization of procurement 
6
Articles with homogeneus green density. No overpressing occurs at the rim areas

TOOL SCHEME

Lower part with membrane and upper punch parts with lining

TOOL SCHEME

Fettling for pressed Articles

Fettling machine to be installed in line with the isostatic press to finish the rim of the articles.

Fettling for pressed Articles
RFM8 fettling machine

FETTLING FOR ROUND ARTICLE

RFM8 rotary table fettling system for the rim finishing of round articles equipped with 8 spindles and 6 fettling stations. Fettling is realized by grinding and sponging.

OFM 8 finishing machine for ceramic tableware

FETTLING FOR NON ROUND ARTICLE

OFM8 rotary table fettling system for the rim finishing of round and non-round articles equipped with 8 spindles and 6 movable fettling stations. Fettling is realized by grinding and sponging. Self-learning system for the precise control of article contour.

ROF 4 universal fettling robot

UNIVERSAL FETTLING WITH ROBOT

ROF Universal fettling system consisting of one to five robots with individual set-up configuration for the rim finishing of round, non-round and asymmetric articles. Fettling is realized by grinding and sponging. Easy programming and teaching of robots.

FETTLING FOR PRESSED CUPS

CFM Universal fettling system as part of isostatic pressing line for cups. Loading/unloading of cups by robot, fettling with deburring, fettling by a grinding disc and three adjustable sponging belts.

Ruota il tuo device.